The largest database of trusted experimental protocols

7 protocols using uv 1601 uv vis spectrometer

1

Steady-State Absorption and Fluorescence Measurements

Check if the same lab product or an alternative is used in the 5 most similar protocols
Steady-state absorption measurements of the samples in toluene were carried out on a Shimadzu UV-1601 UV-vis spectrometer. For all fluorescence measurements, the samples were diluted substantially, corresponding to absorbances <0.1 at the excitation wavelengths. Steady-state fluorescence spectra were recorded on a FluoroMax-4 fluorimeter from Horiba. The raw spectra were corrected for the spectral sensitivity of the instrument and fluctuations of the excitation light source.
+ Open protocol
+ Expand
2

Spectroscopic Characterization of Natural Compounds

Check if the same lab product or an alternative is used in the 5 most similar protocols
Optical rotations were measured at 25 °C with a JASCO Dip-370 digital polarimeter using MeOH as solvent. UV spectra were recorded in MeOH using a Shimadzu UV-1601 UV–Vis spectrometer. ECD spectra were recorded in MeOH on a Jasco 810 spectrometer at 25 °C, using a quartz cell with 1.0 mm optical path length. The 1D and 2D NMR spectra were recorded on a Bruker Avance III 400 NMR instrument at 400 MHz for 1H NMR and 100 MHz for 13C NMR. Chemical shift values (δ) are given in parts per million (ppm), and the coupling constants are in Hz. Low-resolution and high-resolution MS were recorded on Shimadzu LCMS-QP8000α and Agilent G6224A TOF mass spectrometers, respectively. Normal phase column chromatography was performed using Baker silica gel 40 μm flash chromatography packing (J.T. Baker) and reversed phase chromatography was carried out using BAKERBOND C18 40 μm preparative LC packing (J.T. Baker). Analytical and preparative thin-layer chromatography (TLC) were performed on pre-coated plates (0.20 mm thickness) of silica gel 60 F254 (Merck) and RP-18 F254S (Merck). The HPLC purifications were carried out on a Phenomenex Luna 5 μm C18 column (10 × 250 mm) with a Waters Delta Prep system consisting of a PDA 996 detector. The MM2 energy minimizations of possible conformations of compounds were performed using Chem3D 15.0 from PerkinElmer Inc.
+ Open protocol
+ Expand
3

Fluorescent Dye Characterization

Check if the same lab product or an alternative is used in the 5 most similar protocols
Fluorescence and UV-Vis measurements were taken at a concentration of 0.1 mg/mL using a Fluoromax-4 (slit width 2 nm) and a Shimadzu UV-1601 UV/vis spectrometer, respectively. For fluorescein conjugates an excitation of 491 nm and emission of 521 nm was employed. For TAMRA conjugates an excitation of 560 nm and emission of 580 nm was employed.
+ Open protocol
+ Expand
4

Synthesis and Characterization of AuNP-PVA Composites

Check if the same lab product or an alternative is used in the 5 most similar protocols
Chloroauric acid trihydrate and trisodium citrate dihydrate were obtained from Alfa Aesar and used without further purification. The PVA 3 mm filament (Ultimaker) was obtained from Makerpoint. A Shimadzu UV1601 UV–vis spectrometer was used for the UV–vis study. The samples were imaged in a JEOL 1400Plus TEM operating at 120 kV. The mean aspect ratio of the AuNPs was calculated by measuring approximately 800 particles from 24 micrographs. A TE instruments DMA Q800 instrument was used for the mechanical analysis of the plastics using the stress/strain program with a force ramp rate of 1 N/min at isothermal (25 °C) temperature. Four samples of the pure PVA and four samples of the AuNP–PVA materials were tested, where each sample was also flipped upside down and the stress/strain was recorded again. The average of the measurements was used in Figure 2c with the standard deviation shown as the error bar.
+ Open protocol
+ Expand
5

Steady-State Absorption and Fluorescence Measurements

Check if the same lab product or an alternative is used in the 5 most similar protocols
Steady-state absorption measurements of the samples in toluene were carried out on a Shimadzu UV-1601 UV-vis spectrometer. For all fluorescence measurements, the samples were diluted substantially, corresponding to absorbances <0.1 at the excitation wavelengths. Steady-state fluorescence spectra were recorded on a FluoroMax-4 fluorimeter from Horiba. The raw spectra were corrected for the spectral sensitivity of the instrument and fluctuations of the excitation light source.
+ Open protocol
+ Expand
6

Silver Colloid SERS Measurements

Check if the same lab product or an alternative is used in the 5 most similar protocols
Surface enhanced Raman spectroscopy (SERS) measurements were carried out utilizing silver colloids. Silver nanoparticles were prepared by a modification of the synthesis reported by Lee et al. [51] (link). Nanoparticles were obtained with 500 mL of a 0.018 % (m/v) solution of silver nitrate in ultrapure water (18 MΩxcm). The system was heated until the boiling point of water for an hour.
Then, 100 mL of a 0.6% (m/v) solution of ascorbic acid were added to reduce Ag + to Ag 0 . A solution of sodium chloride 0.4 M was used as activating solution. The colloid showed an absorption maximum at 435 nm and FWHM of 160 nm, as measured with a Shimadzu UV-1601 UV-Vis spectrometer (following a 1:3 dilution with ultrapure water to observe maximum absorbance within the instrumental range). SERS measurements were carried out by adding 3µL of colloid directly onto the TLC spots where spectra could be obtained between 2 and 10 min with laser excitation at 785 and 532 nm which remained constant in quality until the evaporation of the liquid. SERS spectra were recorded with an Xplora (Horiba) spectrometer (see Raman spectroscopy).
+ Open protocol
+ Expand
7

Advanced Characterization Techniques for Organometallic Compounds

Check if the same lab product or an alternative is used in the 5 most similar protocols
All experiments and manipulations were carried out under an inert nitrogen atmosphere using standard glovebox or Schlenk techniques unless otherwise indicated. NMR spectra were obtained on a Varian VNMR 700 (699.76 MHz for 1 H; 175.95 MHz for 13 C), a Varian VNMR 500 (500.09 MHz for 1 H; 470.56 MHz for 19 F) or a Varian VNMR 400 spectrometer (399.54 MHz for 1 H; 128.187 for 11 B). 1 H and 13 C chemical shifts are reported in parts per million (ppm) relative to TMS, with the residual solvent peak as an internal reference. 19 F chemical shifts and 11 B chemical shifts are reported in ppm and are referenced on a unified scale, where the single primary reference is the frequency of the residual solvent peak in the 1 H NMR spectrum. Abbreviations used in the NMR data: s, singlet; ; br, broad signal. Mass spectral data were obtained on a Micromass magnetic sector mass spectrometer in electrospray ionization mode. X-ray crystallographic data were collected on a Bruker SMART APEX-I CCD-based X-ray diffractometer. Electronic spectra were collected with a Shimadzu UV-1601 UV-VIS spectrometer (190-1100 nm) with a 4 mL sealed quartz cuvette. Flash chromatography was conducted using a Biotage Isolera One system with cartridges containing high performance silica gel.
+ Open protocol
+ Expand

About PubCompare

Our mission is to provide scientists with the largest repository of trustworthy protocols and intelligent analytical tools, thereby offering them extensive information to design robust protocols aimed at minimizing the risk of failures.

We believe that the most crucial aspect is to grant scientists access to a wide range of reliable sources and new useful tools that surpass human capabilities.

However, we trust in allowing scientists to determine how to construct their own protocols based on this information, as they are the experts in their field.

Ready to get started?

Sign up for free.
Registration takes 20 seconds.
Available from any computer
No download required

Sign up now

Revolutionizing how scientists
search and build protocols!