The largest database of trusted experimental protocols

7000c gc ms triple quad

Manufactured by Agilent Technologies
Sourced in United States

The 7000C GC/MS Triple Quad is a gas chromatography-mass spectrometry (GC/MS) system designed for sensitive and quantitative analysis of complex samples. It features a triple quadrupole mass analyzer that provides high-performance tandem mass spectrometry (MS/MS) capabilities. The system is capable of performing accurate and precise measurements of target analytes in a wide range of applications.

Automatically generated - may contain errors

7 protocols using 7000c gc ms triple quad

1

GC-TQ-MS/MS Analysis of Organic Compounds

Check if the same lab product or an alternative is used in the 5 most similar protocols
GC-TQ-MS/MS was performed on an Agilent 7890B GC system equipped with a 7000 C GC/MS Triple Quad. For the DB-5MS (15 m × 0.25 mm × 0.1 μm) capillary column, splitless injection was performed at 250 °C. The GC oven temperature was adjusted according to the following program: an initial temperature of 50 °C was maintained for 1 min, followed by an increase to 200 °C at a rate of 40 °C·min−1, an increase to 240 °C at a rate of 20 °C·min−1, an increase to 246 °C at a rate of 1.5 °C·min−1, and an increase to 300 °C at a rate of 40 °C·min−1, with the final temperature being maintained for 3 min. For the DB-5MS (30 m × 0.25 mm × 0.1 μm) column, the oven temperature program was as follows: 50 °C isothermal for 1 min, increased to 240 °C at 50 °C·min−1, increased to 255 °C at 1.5 °C·min−1, increased to 300 °C at 50 °C·min−1 and maintained at the final temperature for 1 min. Helium was used as the carrier gas at a flow rate of 1 mL·min−1. The inlet temperature was set to 300 °C, the ion trap temperature was 250 °C, the electron energy was 70 eV, and the spectra were recorded over a range of 10-400 m/z. Qualitative Analysis software (B.07.00) was used for data analysis.
+ Open protocol
+ Expand
2

Lipid Extraction and Derivatization for GC-MS

Check if the same lab product or an alternative is used in the 5 most similar protocols
Transfected HeLa and MCF7 cells were harvested and washed two twice with ice‐cold PBS. Lipid was extracted using 1 000 μl of extracting solution made using ice‐cold methanol, acetonitrile, choloroform and water at ratio of 2:2:2:1 (v/v). The lower phase containing lipid was then isolated and air dried using rotary evaporator. Dried lipids were resuspended in N,O‐Bis(trimethylsilyl)trifluoroacetamide (BSTFA) containing 1% trimethylsilyl choloride (TMCS). Lipids were mixed well and heated to 60°C for up to 30 min until all liquid content is evaporated. Followed by cooling at room temperature and then resuspended in chloroform. Derivatised lipids were injected into gas chromatography‐tandem mass spectroscopy (GC‐MS; 7000C GC/MS Triple Quad, Agilent Technologies).
+ Open protocol
+ Expand
3

GC-MS Analysis of Arctostaphylos uva-ursi

Check if the same lab product or an alternative is used in the 5 most similar protocols
Gas chromatography (Agilent 7000C GC/MS Triple Quad, Santa Clara, CA, USA) equipped with an HP-5MS column (length = 30 m; diameter = 0.25 mm; film thickness = 0.25 m) mass spectrometer programmed at temperature 30–280/300 °C with a hold time of 5 min and rate of 10 °C/min was used to investigate bioactive compounds in methanol extract of dried Arctostaphylos uva-ursi. The chromatography conditions were as follows: column flow rate of 1 mL/min, injection mode split, and carrier gas Helium 99.999%. GC-MS spectra with mass library search (National Institute of Standards and Technology, Bureau Drive Gaithersburg, MD, USA, based AMDIS software) and relative retention indices were used to identify the components [42 (link)].
+ Open protocol
+ Expand
4

GC-MS/MS Analysis of Pesticides

Check if the same lab product or an alternative is used in the 5 most similar protocols
An Agilent GC 7890B system (Agilent Technologies) equipped with a 7000C GC/MS triple quad (Agilent Technologies) and an Agilent HP-5MS column (30 m×0.25 mm i.d., 0.25 mm) were used for pesticide analysis. The mobile phase was helium gas (99.9999% purity), with a constant flow rate of 1.5 mL min−1. The column oven temperature was initially held at 90°C for 1 min, increased at 15°C min−1 to 180°C and held for 1 min, and finally, increased at 8°C min−1 to 300°C and held for 3 min. The temperature of both the injection port and the transfer line was 250°C. The Agilent 7693 autosampler (Agilent Technologies) was programmed to inject volume as 1 µL into the splitless injection port. Syringe washing was performed twice with two solvents (washing port A: distilled water : methanol at a 6 : 4 ratio; washing port B: acetone : methanol at a 5 : 5 ratio). The triple-quad MS was operated in selected reaction monitoring (SRM) mode with an electron energy of 70 eV and an emission current of 35 mA. Nitrogen was used as the collision gas, with a flow rate of 1.5 mL min−1. Details of the GC-MS/MS analysis parameters for pesticides are given in Supplementary Table 1.
+ Open protocol
+ Expand
5

Volatile Compound Profiling of Fruit Samples

Check if the same lab product or an alternative is used in the 5 most similar protocols
The characteristic VOCs were extracted using a solid-phase microextraction (SPME) method [31 (link),32 (link),33 (link),34 (link)]. For each sample, 5 g of fruit was ground and added to a headspace vial. The non-polar divinylbenzene/carboxen/polydimethylsiloxane (DVB/CAR/PDMS) fibers then penetrated the septa to extract the volatiles for 40 min at 45 °C. GC-MS analysis was carried out on a 7890B GC System with a 7000C GC-MS Triple Quad mass detector (Agilent Technologies, Santa Clara, USA). The SPME fiber was quickly inserted into the GC-MS system and thermally desorbed at 250 °C for 3 min. Helium of high purity (99.999%) was used as the carrier gas, and the flow rate was maintained at 1.0 mL min–1. The column temperature was increased following a heating program, with an initial temperature of 50 °C maintained for 3 min, followed by a 10 °C min–1 ramp to 250 °C and a 5 min holding period. The mass spectra were analyzed using the NIST17.L library.
+ Open protocol
+ Expand
6

Analytical Characterization of Chemical Compounds

Check if the same lab product or an alternative is used in the 5 most similar protocols
The reagents and solvents were commercially available for analytical reagent (AR) grade and were used as received or were dried prior to use, as needed. The melting point was measured by X-5 binocular microscope melting point apparatus (Beijing Tech Instruments Co. Ltd., Beijing, China). Using dimethyl sulfoxide (DMSO-d6) as solvent and tetramethylsilane (TMS) as the internal standard, 1H-NMR spectra were recorded on 300 MHz and 600 MHz spectrometers and 13C-NMR spectra were recorded on 75 MHz and 151 MHz spectrometers (Bruker, Karlsruhe, Germany). MS data were obtained on the 7000C Triple Quad GC/MS and 6460 Triple Quad LC/MS Mass Spectrometers (Agilent Technologies, Santa Clara, CA, USA). Elemental analyses were determined on a Vario EL III elemental analyser (Elementar Analysensysteme GmbH, Frankfurt, Germany).
+ Open protocol
+ Expand
7

Purification and Characterization of Chemical Compounds

Check if the same lab product or an alternative is used in the 5 most similar protocols
All solvents and reagents were commercially available for analytical reagent (AR) grade and dried prior to use. Column chromatography (Silica gel: 200–300 mesh) was used to purify target compounds. The melting points were determined by the X-5 binocular microscope melting point apparatus (Beijing Tech Instrument Co. Ltd., Beijing, China). 1H-NMR and 13C-NMR spectra were recorded on a Bruker 600 MHz and 101 MHz spectrometer (Bruker, Karlsruhe, Germany), using dimethyl sulfoxide (DMSO-d6) as solvent and tetramethylsilane (TMS) as the internal standard. MS data were obtained on the 7000C Triple Quad GC/MS and 6460 Triple Quad LC/MS Mass Spectrometers (Agilent Technologies, Santa Clara, CA, USA).
+ Open protocol
+ Expand

About PubCompare

Our mission is to provide scientists with the largest repository of trustworthy protocols and intelligent analytical tools, thereby offering them extensive information to design robust protocols aimed at minimizing the risk of failures.

We believe that the most crucial aspect is to grant scientists access to a wide range of reliable sources and new useful tools that surpass human capabilities.

However, we trust in allowing scientists to determine how to construct their own protocols based on this information, as they are the experts in their field.

Ready to get started?

Sign up for free.
Registration takes 20 seconds.
Available from any computer
No download required

Sign up now

Revolutionizing how scientists
search and build protocols!